Grafting Grape Vines

Grapes April 14, 2013|Print

Cleft grafts       Bark grafts       Whip grafts       Budding       More info

Eric Stafne, Mississippi State University

Grafting or budding is an asexual propagation technique. This is the process of placing a shoot system (a scion) of one cultivar or species on the root system (a rootstock) of another. When grafting, the scion will contain multiple buds, but budding consists of a single bud. The only requirement for grafting and budding is viable cambium contact. The cambium is a single layer of cells located just below the bark. This area leads to the formation of the graft union of the scion and rootstock. It is subject to drying out, so take steps to prevent that situation. Increased cambial contact (the more area that touches) between scion and rootstock increases the chances of success.

Successful Grafting

Grafting is a time-consuming process requiring patience and practice. Already existing vines are candidates for grafting if the cultivar is not economical or not appropriate for the site. The vines to be grafted must be healthy and vigorous, without disease or insects, and relatively young. Scion wood collection is the same as for taking cuttings. The scion is taken while dormant for most types of grafting; however, actively growing tissue can be used in some cases. There are several types of grafts that can be used, including:

  • Cleft grafts
  • Bark grafts
  • Whip grafts
  • Budded grafts
  • Green growing bench grafts
The cleft grafting technique.

The cleft graft is a simple method that requires little skill. It is for larger diameter vines and the scion must be dormant. There is a five step process for the cleft graft:

  1. Cut off the top of the vine about 30 minutes or so before grafting.
  2. Split the rootstock with a blade or chisel.
  3. Hold the split open and prepare the scions by cutting one end to a “v” shape.
  4. Place one scion on each side to fit with the cambium.
  5. Tape the split area together and use grafting compound to seal the splits to keep excess moisture out and seal moisture in.

The bark graft is also relatively easy and requires little skill to make it successful. The bark must be “slipping” for this graft to work, so timing can vary from rootstock to rootstock. The scion must be dormant. The bark grafting process is:

  1. Select the vine and cut off the top.
  2. Prepare the scion by cutting a pattern into the basal end.
  3. Make matching pattern cuts on the rootstock.
  4. Insert scion and secure it to the rootstock with a grafting band or tape.
  5. Cover the area and seal the cut with grafting wax.

Whip grafting is a common way to propagate many different plants. For the rootstock, use 1- to 2-year old vines, up to 3/4-inch in diameter. The scion size should match with the size of the rootstock. This type of graft can be done in the field or in the greenhouse. The process of whip grafting is:

  1. Cut the scion at an angle about 1 to 2 inches long.
  2. Cut the rootstock at an angle at the same length.
  3. Match up the cambiums.
  4. Cut a tongue in both the scion and the rootstock.
  5. Wrap the graft and seal it.
Budding.

Budding is somewhat different from grafting in that only one bud is used. Budding has many variations, but T-budding (also called shield budding) is commonly used in fruit species. Buds for T-budding must be mature and dormant, taken from healthy and vigorous wood.

  1. Remove the leaf blade, leaving only the petiole intact, which acts as a handle.
  2. Shave the bud off the budwood. You only need a small sliver of wood.
  3. On the rootstock, make a vertical cut to separate the bark from the cambium, then make a perpendicular cut at the top of the vertical cut to form a “T.”
  4. Carefully peel back the bark to expose the pocket for the bud shield.
  5. Slide the bud shield into the open pocket and trim off the top if needed.
  6. Wrap tightly with grafting tape, but leave the bud exposed.
  7. After the healing process starts and you observe growth, you can remove the rootstock that was left above the budded area.

There is a rapid graft propagation technique where the callused graft is rooted under mist for 30 days, grown in a greenhouse for 30 days, conditioned in a lath house for 30 days and planted in the vineyard in mid to late spring (May, in northern areas). Vines from this system are called green growing bench grafts. Summer temperatures, sunlight, and low humidity can make green growing bench grafts very difficult to establish.

Recommended Resources

Grafting and Budding, North Carolina State University

Budding, University of Missouri

Chip Budding

Grafting Fruit Trees video

Field Grafting Young Grapevines, Oregon State University

 

 

Reviewed by Jodi Creasap Gee, Cornell University

and Jim Wolpert, UC Davis

Connect with us

  • Twitter
  • Facebook
  • YouTube

Welcome

eXtension is an interactive learning environment delivering research-based information emerging from America's land-grant university system.

LOCATE

Donate to Grapes

Your donation keeps eXtension growing.

Give Now